Interface: NDOT District 2 Field Equipment - NDOT District 2 Road Operations Center
Architecture Flow Definitions
automated lane control data (Existing) Applicable ITS Standards
Control commands and operating parameters provided to RSEs that control and monitor automated vehicle operations, including tightly coupled platooned groups of vehicles operating in dedicated or mixed–mode lanes. This flow includes platoon parameters including maximum platoon size, target speeds and gaps, and vehicle restrictions.
automated lane status (Existing) Applicable ITS Standards
Current operational status of lanes supporting automated vehicle operations. The flow includes the status of the RSEs, associated field equipment, and vehicles using the facility.
data collection and monitoring control (Existing) Applicable ITS Standards
Information used to configure and control data collection and monitoring systems.
environmental sensors control (Existing) Applicable ITS Standards
Data used to configure and control environmental sensors.
field equipment status (Existing) Applicable ITS Standards
Reports from field equipment (sensors, signals, signs, controllers, etc.) which indicate current operational status.
lane management control (Existing) Applicable ITS Standards
Information used to configure and control dynamic lane management systems.
lane management information (Existing) Applicable ITS Standards
System status of managed lanes including current operational state, violations, and logged information. This includes lane usage information including both traditional traffic flow measures and special information associated with managed lanes such as measured passenger occupancies. It also includes the operational status of the lane management equipment.
rail crossing blockage notification (Existing) Applicable ITS Standards
Notification that a highway–rail intersection is obstructed and supporting information.
rail crossing control data (Existing) Applicable ITS Standards
Data required for HRI information transmitted at railroad grade crossings and within railroad operations.
rail crossing request (Existing) Applicable ITS Standards
A request for highway–rail intersection status or a specific control request intended to modify HRI operation.
rail crossing status (Existing) Applicable ITS Standards
Status of the highway–rail intersection equipment including both the current state or mode of operation and the current equipment condition.
reversible lane control (Existing) Applicable ITS Standards
Control of automated reversible lane configuration and driver information systems.
right-of-way request notification (Existing) Applicable ITS Standards
Notice that a request has occurred for signal prioritization, signal preemption, pedestrian call, multi–modal crossing activation, or other source for right–of–way.
roadside archive data (Existing) Applicable ITS Standards
A broad set of data derived from roadside sensors that includes current traffic conditions, environmental conditions, and any other data that can be directly collected by roadside sensors. This data also indicates the status of the sensors and reports of any identified sensor faults.
roadway dynamic signage data (Existing) Applicable ITS Standards
Information used to initialize, configure, and control dynamic message signs. This flow can provide message content and delivery attributes, local message store maintenance requests, control mode commands, status queries, and all other commands and associated parameters that support remote management of these systems.
roadway dynamic signage status (Existing) Applicable ITS Standards
Current operating status of dynamic message signs, highway advisory radios, or other configurable field equipment that provides dynamic information to the driver.
roadway treatment system control (Existing) Applicable ITS Standards
Control data for remotely located, automated devices, that treat the road surface (e.g., de–icing applications).
roadway treatment system status (Existing) Applicable ITS Standards
Current operational status of automated roadway treatment devices (e.g., anti–icing systems).
safeguard system control (Existing) Applicable ITS Standards
Data that controls safeguard systems (remotely controlled equipment used to mitigate the impact of incidents on transportation infrastructure, such as blast shields, exhaust systems, etc.).
shoulder management control (Existing) Applicable ITS Standards
Information used to configure and control systems that allow use of a shoulder as a lane for vehicular traffic.
signal control commands (Existing) Applicable ITS Standards
Control of traffic signal controllers or field masters including clock synchronization.
signal control device configuration (Existing) Applicable ITS Standards
Data used to configure traffic signal control equipment including local controllers and system masters.
signal control plans (Existing) Applicable ITS Standards
Traffic signal timing parameters including minimum green time and interval durations for basic operation and cycle length, splits, offset, phase sequence, etc. for coordinated systems.
signal control status (Existing) Applicable ITS Standards
Operational and status data of traffic signal control equipment including operating condition and current indications.
signal fault data (Existing) Applicable ITS Standards
Faults reported by traffic signal control equipment.
signal system configuration (Existing) Applicable ITS Standards
Data used to configure traffic signal systems including configuring control sections and mode of operation (time based or traffic responsive).
speed monitoring control (Existing) Applicable ITS Standards
Information used to configure and control automated speed monitoring, speed warning, and speed enforcement systems.
speed monitoring information (Existing) Applicable ITS Standards
System status including current operational state and logged information including measured speeds, warning messages displayed, and violation records.
traffic detector control (Existing) Applicable ITS Standards
Information used to configure and control traffic detector systems such as inductive loop detectors and machine vision sensors.
traffic detector data (Existing) Applicable ITS Standards
Raw and/or processed traffic detector data which allows derivation of traffic flow variables (e.g., speed, volume, and density measures) and associated information (e.g., congestion, potential incidents). This flow includes the traffic data and the operational status of the traffic sensor system.
traffic images (Existing) Applicable ITS Standards
High fidelity, real–time traffic images suitable for surveillance monitoring by the operator or for use in machine vision applications. This flow includes the images and meta data that describes the images.
traffic metering control (Existing) Applicable ITS Standards
Control commands and operating parameters for ramp meters, interchange meters, mainline meters, and other systems equipment associated with roadway metering operations.
traffic metering status (Existing) Applicable ITS Standards
Current operational status and operating parameters for ramp meters, interchange meters, mainline meters and other control equipment associated with roadway metering operations.
variable speed limit control (Planned) Applicable ITS Standards
Information used to configure and control variable speed limit systems including the equipment used to provide current speed limits and other information to drivers and the equipment used to monitor traffic and environmental conditions along the roadway.
variable speed limit status (Planned) Applicable ITS Standards
Current operating status of the variable speed limit systems including the state of the equipment.
video surveillance control (Existing) Applicable ITS Standards
Information used to configure and control video surveillance systems.
work zone warning device control (Existing) Applicable ITS Standards
Data used to configure and control work zone safety monitoring and warning devices.
work zone warning status (Existing) Applicable ITS Standards
Status of a work zone safety monitoring and warning devices. This flow documents system activations and includes additional supporting information (e.g., an image) that allows verification of the alarm.